Updated Nov 22, 2026· 10 min read

Our Top Picks

  1. RAM Mounts Fish Finder and GPS Mount withMedium Arm6.25 x 2 x 8 inches1 pounds
    Check on Amazon
  2. YakAttack Round Base Fish Finder Mount for KayakOne Size1 x 1 x 1 inches0.01 pounds
    Check on Amazon
  3. Double Face Marine Electronic Mount24 inches0.01 x 0.01 x 0.01 inches0 pounds
    Check on Amazon
  4. Scotty 0368 Universal Sounder MountOne Size10 x 5 x 2 inches0.35 pounds
    Check on Amazon
  5. RAM MOUNTS Heavy-Duty Fish Finder Mount with DShort Arm3.68 x 11 x 8.1 inches3.7 pounds
    Check on Amazon

A sonar screen only earns its place on the boat when it stays pointed at your eyes. Chop, wakes, and engine vibration all work to shake a display loose, tilt it toward the sky, or bury it in glare, and a weak mount turns good electronics into a distraction. The mount is the link between the head unit and the deck, and it decides how much of your attention goes to the water instead of the hardware.

Our top pick: RAM Mounts RAM-111U Drill-Down Marine Electronics Mount. Runner-up: YakAttack Round Base Fish Finder Mount with LockNLoad.

This guide covers display mounts only: the arms, bases, and plates that hold the screen. It does not cover transducers, cables, or the fish finders themselves. The five picks below span the main mounting styles, from a ball-and-socket arm for a bass boat console to a track mount that slides into a kayak rail, a swivel base for shared viewing, a quick-release post for anglers who move between boats, and a heavy-duty build for the largest displays.

As an Amazon Associate, we earn from qualifying purchases.

Quick answer

For most boats, the RAM Mounts RAM-111U is the mount to buy: its 1.5-inch ball-and-socket arm holds mid-size displays steady and adjusts with one knob. Kayak anglers should pick the YakAttack LockNLoad track mount, while owners of large 9- to 12-inch screens need the heavy-duty RAM-D-111U-C and its 2.25-inch ball.

RAM Mounts RAM-111U Drill-Down Marine Electronics Mount

The RAM-111U is the ball-and-socket mount that the rest of the category gets measured against, and it takes the top spot here. The kit pairs a 2.5-inch round base with the universal AMPS hole pattern, a medium double socket arm, and a flat 6.25 by 2-inch rectangular top plate drilled with several hole and slot combinations, giving an overall height of 7.35 inches. The display bracket bolts to the top plate, and the 1.5-inch C-size ball at each end of the arm lets the screen tilt, turn, and swing to almost any angle before one knob locks the whole assembly down.

Construction is powder-coated marine-grade aluminum, and the rubber ball surface grips firmly while soaking up some of the shock that runs through a hull in rough water. RAM rates the C-size system for up to 4 pounds in standard duty, which covers the mid-size units most anglers run, and the company backs the mount with a lifetime warranty. Because the system is modular, a worn arm or a different base can be swapped without replacing the whole mount.

The drill-down base does demand a flat patch of console or deck and four screws, so it suits a permanent install on a powerboat better than a rental or a borrowed hull. Check that the top plate pattern lines up with your unit’s gimbal bracket before ordering.

YakAttack Round Base Fish Finder Mount with LockNLoad

Kayak anglers usually refuse to drill holes in a hull, and the YakAttack Round Base mount is built around that refusal. Its LockNLoad base slides into a kayak track and clamps down with a locked connection that resists slipping or rotating in the rail, a common failure of ball mounts used on tracks. YakAttack lists compatibility with its own GearTrac, MightyMount II, and MightyMount XL, plus most other factory-installed kayak track systems, and mounting hardware is included in the box.

The round base plate carries the 3-hole pattern used by units such as the Garmin Striker 4 and the Raymarine Dragonfly 7 Pro, and the mount is designed to replace the factory base on those finders for a clean, low install. The whole unit lifts off the track quickly at the launch, which matters when the kayak rides on a roof rack or the electronics come indoors between trips. YakAttack builds the mount in the USA.

Fit is the watch-out. The round plate only suits displays with that 3-hole round base pattern, so owners of larger gimbal-bracket units need one of YakAttack’s rectangular or model-specific LockNLoad plates instead. A few kayak brands need an adapter for their tracks, and neither the fish finder nor the track itself is included.

Millennium Marine Double Face Marine Electronic Mount

Some boats carry two anglers facing each other, and the Millennium Marine Double Face mount is built for exactly that layout. True to its name, the mount presents a mounting face on each side of its post, so one display can serve the angler in front while a second faces the partner behind, a setup common on spider-rigging and crappie boats. A single post and base support both screens instead of two separate mounts competing for deck space.

The base swivels 350 degrees, so either viewer can swing the assembly toward their seat, and the post height adjusts to lift the screens above rod tips and rail clutter. Construction is anodized aluminum, which shrugs off the wet, sun-heavy environment of an open boat, and the mounting plate is drilled to fit most monitors. The model number for this mount is MM-002-BL.

The design only makes sense when two viewing positions genuinely share a helm area. A solo angler pays for a second face that never holds a screen, and the fixed post footprint needs a solid, flat mounting surface with room to rotate. Confirm the plate pattern against your display bracket, since wide units can crowd the post when two are fitted back to back.

Scotty 368 Universal Sounder Mount

Boats already fitted with Scotty bases gain the simplest route to a sonar screen: the Scotty 368. Its multi-pattern universal top plate is drilled to accept the gimbal brackets of most popular fish finder brands, including Garmin, Humminbird, and Lowrance units in the compact classes, and the plate sits on Scotty’s patented post. Drop the post into a Scotty base, and the display lifts straight out again when you leave the boat, with no tools and no loose hardware to chase around the deck.

That post connection also gives the mount its adjustment. The post rotates freely in the base for an infinitely adjustable viewing angle, then locks at the position you choose, so the screen can face the bow seat while fishing forward and swing toward the stern when a fish comes to the net. The mount is molded nylon, light and immune to rust, and it keeps the whole electronics package removable for storage or for moving between two boats that share the Scotty system.

The trade-offs are clear in the listing: the sounder itself, the No. 241 side or deck base, and the fasteners are not included, so a boat with no Scotty base yet needs that extra purchase. Nylon also flexes more than aluminum under a heavy screen, which keeps this mount best suited to smaller displays.

RAM Mounts RAM-D-111U-C Large Marine Electronics Mount

Big screens change the math. A 9- to 12-inch display carries real weight high above its bracket, and a mid-size ball can creep under that load on a fast run. The RAM-D-111U-C answers with RAM’s D-size system: a 2.25-inch ball, a short double socket arm, and a long 3 by 11-inch rectangular plate that spreads the bracket load across a wide footprint. The short arm is deliberate, keeping the heavy display close to the base where leverage works against it least.

Like the smaller RAM-111U, the mount is powder-coated marine-grade aluminum with the universal hole patterns that match gimbal brackets from Garmin, Lowrance, Humminbird, and other major brands, and it carries the same lifetime warranty. The ball-and-socket joint still gives full tilt and rotation for glare control, but once the knob is set, the oversize ball’s clamping area holds the angle far more stubbornly than a C-size joint under the same screen.

This is more mount than a compact unit will ever need, and the plate’s length demands a generous flat area of console. Anglers running a single large graph at the helm, or pairing this size class at the bow, are the audience; anyone with a 7-inch screen should save the deck space and choose the C-size version instead.

How to choose

Begin with the display itself. Note its weight and the hole pattern on its gimbal bracket, because every mount in this guide holds the bracket rather than the screen. Compact units ride happily on post mounts and track plates, mid-size screens belong on a 1.5-inch C-size ball, and displays in the 9- to 12-inch class need the 2.25-inch D-size ball or an equally stout base. A mount that is undersized for its screen will creep and sag no matter how carefully it is tightened.

Next, match the base to the boat. A console with a flat, open patch of fiberglass takes a drill-down base well. Kayaks with factory tracks call for a track mount that locks into the rail. Boats already carrying Scotty bases can add a post mount in seconds, and shared two-angler layouts are the one case where a double-face swivel post earns its footprint.

Then weigh removal. Anglers who trailer with electronics removed, fish from more than one hull, or store gear indoors should favor quick-release post and track systems. A permanent helm install can accept a bolted ball mount and gain stiffness in return. Finally, favor marine-grade aluminum, anodized finishes, and stainless or nylon hardware in salt or brackish water, and confirm what the box leaves out, since bases, adapters, and fasteners are often sold separately.

Who should skip

Skip this entire category if your fish finder already sits in a flush console cutout or on a factory bracket that holds its angle through a full day on the water; a mount solves wobble and viewing problems, and a solid factory setup has neither. Pedal and paddle anglers in very small kayaks should also think twice, since a tall mount raises the screen into paddle swing and can crowd a tight cockpit.

Skip the heavy-duty D-size mount if your display is 7 inches or smaller, and skip post and track mounts if your boat has no compatible base or rail and you are unwilling to add one. Anglers who only fish rented or club boats should look at clamp and suction options rather than anything in this guide, since every pick here assumes a base you own.

Frequently Asked Questions

Will these mounts fit my fish finder?

Most likely, provided the hole pattern matches. Universal plates from RAM and Scotty are drilled with several patterns that line up with the gimbal brackets of major brands such as Garmin, Lowrance, and Humminbird. Measure your bracket’s bolt spacing and compare it with the plate dimensions in the listing before ordering, since screen size alone does not guarantee a match.

Do I need a separate base for the Scotty 368?

Yes. The 368 is the top plate and post only. It drops into a Scotty post base, such as the No. 241 side or deck mount, which is sold separately along with the fasteners. Boats that already carry Scotty rod holder bases usually have the socket the 368 needs, which is where the mount makes the most sense.

Can a kayak track mount hold a large display?

Track mounts suit compact and mid-size units best. The YakAttack LockNLoad plate in this guide is built for round-base finders such as the Striker 4 class, and YakAttack sells other plates for larger gimbal units. Very large screens raise the center of gravity on a narrow hull, so most kayak anglers keep displays modest regardless of the mount.

What ball size should I choose for a 10-inch screen?

Choose the 2.25-inch D-size system. RAM’s sizing guidance places 9- to 12-inch displays on the D-size ball because the larger joint offers the clamping area a heavy screen needs in chop. The 1.5-inch C-size ball is the right match for mid-size units, and using it under an oversize display invites slow sagging at speed.

Final verdict

For a typical powerboat helm, the RAM Mounts RAM-111U remains the safest single purchase: proven ball-and-socket adjustment, marine-grade aluminum, and a plate pattern that fits most mid-size brackets. Kayak anglers should go straight to the YakAttack LockNLoad for a locked, drill-free track install, and anyone running a 9- to 12-inch graph should step up to the RAM-D-111U-C without hesitation. The Scotty 368 rewards boats already rigged with Scotty bases, while the Millennium Marine Double Face solves the two-angler viewing problem nothing else here addresses. Match the mount to the screen weight and the base your boat can accept, and the display will hold its angle all season.

Product and ASIN Reference

Product ASIN
RAM Mounts RAM-111U Drill-Down Marine Electronics Mount B0000AXXZH
YakAttack Round Base Fish Finder Mount with LockNLoad B07G7BLBMB
Millennium Marine Double Face Marine Electronic Mount B0C1M8L74H
Scotty 368 Universal Sounder Mount B00FPQZ95K
RAM Mounts RAM-D-111U-C Large Marine Electronics Mount B001F0MFXY
M
Mark Reynolds
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.

FAQ

Will these mounts fit my fish finder?
Most likely, provided the hole pattern matches. Universal plates from RAM and Scotty are drilled with several patterns that line up with the gimbal brackets of major brands such as Garmin, Lowrance, and Humminbird. Measure your bracket’s bolt spacing and compare it with the plate dimensions in the listing before ordering, since screen size alone does not guarantee a match.
Do I need a separate base for the Scotty 368?
Yes. The 368 is the top plate and post only. It drops into a Scotty post base, such as the No. 241 side or deck mount, which is sold separately along with the fasteners. Boats that already carry Scotty rod holder bases usually have the socket the 368 needs, which is where the mount makes the most sense.
Can a kayak track mount hold a large display?
Track mounts suit compact and mid-size units best. The YakAttack LockNLoad plate in this guide is built for round-base finders such as the Striker 4 class, and YakAttack sells other plates for larger gimbal units. Very large screens raise the center of gravity on a narrow hull, so most kayak anglers keep displays modest regardless of the mount.
What ball size should I choose for a 10-inch screen?
Choose the 2.25-inch D-size system. RAM’s sizing guidance places 9- to 12-inch displays on the D-size ball because the larger joint offers the clamping area a heavy screen needs in chop. The 1.5-inch C-size ball is the right match for mid-size units, and using it under an oversize display invites slow sagging at speed.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Fish Finder Mounts for Stable Sonar Views…Check price on Amazon

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Prime for Young Adults

A Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.

See Prime for Young Adults
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.